1495.95 $ USD NeedsWings Aluminum Intake Manifolds - United States

Published date: December 23, 2014
  • Location: Warren, Michigan, United States

Part#: srt6IM

Designed and built with pride in the USA. These performance intake manifolds will take your SRT6 or SLK32 AMG to a new level. These are a direct replacement to the factory intake manifolds. Utilizing larger mandrel bent billet aluminum tubing and an enlarged tuned plenum these manifolds flow almost double that of the factory intake manifolds! We have over a year of R&D and flow testing before we attached our logo onto them. This will most likely be the nicest and best flowing part on your car. Each set of these intake manifolds get around 20 hours of labor! We add a 1/8NPT bung to the passenger side manifold tubing for use with a boost sensor for your boost gauge (designed with the Zeitronix boost sensor but can also be used with other electronic boost gauges) and close it off with a plug incase you are not ready to install your gauges yet. This bung could be welded to the drivers side if you would prefer, please put that into the special instructions at checkout.

Once professionally built and pressure tested, the intake manifolds are then internally ported/polished around the intake ports and thru the distribution tube going into the plenum. They are then professionally “decked” on the underside mating surfaces to ensure a proper seal. From there they are then Teflon coated for both the internal flow increase and also the Teflon is tinted in order for the external appearance. The Teflon can be tinted a wide range of colors but specific color match is difficult. Inquire if you are interested in a custom color.

The manifolds are then pressure tested for their 3rd time and fitted with all new stainless polished intake manifold bolts and washers along with 2 sets (4 total) of our rubber/cork intake manifold gaskets which have been proven to hold more boost then you can throw at them.

We now have some more friendly colors for the thermal coating which includes Silver, Black, Red, Yellow or Blue. Please specify your preference in the SPECIAL INSTRUCTIONS section at checkout.


The factory SRT6 drivers side intake manifold flowed 255-260cfm @ 28 In. of H2O
Our driver’s side intake manifold BEFORE the Teflon coating flowed 455-460cfm @ 28 In. of H2O
Same drivers side manifold AFTER the Teflon coating flowed 480-485cfm @ 28 In. of H2O

Note: above numbers were from one manifold, together these should be able to flow 960-970cfm!!!!!!

The NeedsWings Y-Pipe is recommended with these manifolds to compliment each other (y-pipe is sold separately).

A specific tune is available thru InMotionTuning for these manifolds and is highly recommended! (Sold separately thru InMotion Tuning ) You will want the "Full Custom Chip Tuning". With the oem pcm calibration and our Cold Air Intake, ASP pulleys and these new manifolds the pcm was not delivering enough fuel for our liking. We have worked with inmotion to "fatten" up the fuel curve to our ideal Air Fuel Ratio and have dialed in this tune at every 100 rpm's!

The dyno chart below shows the gains on our Chrysler Crossfire SRT6 with NeedsWings Cold Air Intake, ASP Pulleys, and InMotion Base Tune already installed. The gains are after installing the new manifolds, Y-pipe, custom tune and a few minutes of street driving for the pcm to adjust to the new air volume. We pulled back into the dyno and strapped it back down and saw an avarage increase of 44 wheel horsepower and 22 ft/lbs of torque! Same dyno, same day.

The “SUPERCHARGED” emblems are free option that can be added to the top of the manifolds if you choose. The intake manifolds will come with our NEEDSWINGS logo on the outer sides and without the SUPERCHARGED emblems by default. If you would like the SUPERCHARGED emblems on top please mention it in the special instructions section during checkout.

As these are custom made to order, please expect 3-4 weeks for delivery.

Vote
Result 0 votes
NeedsWings
0 votes

Filter by following factors:

Condition:
Parts compatibility:
Shipping:
Share by email Share on Facebook Share on Twitter Share on Google+

Share

Useful information

  • Avoid scams by acting locally or paying with PayPal
  • Never pay with Western Union, Moneygram or other anonymous payment services
  • Don't buy or sell outside of your country. Don't accept cashier cheques from outside your country
  • This site is never involved in any transaction, and does not handle payments, shipping, guarantee transactions, provide escrow services, or offer "buyer protection" or "seller certification"

Related listings

  • NeedsWings SRT6 Crossfire Thermal Coated Dual Cold Air Intake System
    NeedsWings SRT6 Crossfire Thermal Coated Dual Cold Air Intake System
    Intake - United States (Michigan) - December 23, 2014 999.95 $ USD

    Part#: srt6tdcai This product includes everything from our dual CAI and we then have the exterior of the main tubes coated with a Thermal coating and still do the teflon velocity coating on the inside. This gives us the best of both worlds so to spea...

  • Crossfire Cold Air Intake System
    Crossfire Cold Air Intake System
    Intake - United States (Michigan) - December 23, 2014 449.95 $ USD

    Designed and built in "Motor City" Detroit Michigan, we used the finest materials for creating this world class part. Our SRT6 Crossfire Cold Air Intake system replaces the factory intake system completely. We use 6061 Mandrel bent 3" Aluminum tubing...

  • Air Intake Temperature Sensor
    Air Intake Temperature Sensor
    Intake - United States (Michigan) - December 23, 2014 27.95 $ USD

    Part#: c32AIT This is a factory replacement Air Intake Temperature sensor, it is located in the lower Y pipe after the intercooler on the c32, slk32 or SRT6 supercharged motors. Also used on the v8 m113k motors.